High-frequency power ceramic dielectric capacitor

High-frequency power ceramic dielectric capacitor

Get Latest Price

Min. Order:

Makipag-ugnay sa Ngayon

Paglalarawan ng Produkto

Mga katangian ng produkto

Pagbalot at Paghahatid

Paglalarawan ng Produkto

Mga katangian ng produkto

Model No.: DLC70L(130130)

Pagbalot at Paghahatid

The file is encrypted. Please fill in the following information to continue accessing it

Paglalarawan ng Produkto

Ang DLC70L ay isang High Power RF Microwave Ceramic Capacitor

DLC70LHigh-frequency power ceramic dielectric capacitor
Nagtatampok ng mataas na Q factor, mababang ESR at ESL, mababang ingay at mataas na pagiging maaasahan, ang produktong ito ay makatiis ng mataas na RF current, boltahe at kapangyarihan. Malawak itong ginagamit sa paggawa ng semiconductor, induction heating, inductively coupled plasma system, mga instrumentong pang-agham, kagamitang medikal, high-energy RF power transmission at pagtutugma ng mga circuit.

Talahanayan ng Kapasidad ng DLC70L

Capacitance (pF)	Code	Tolerance	Rated Voltage	Capacitance (pF)	Code	Tolerance	Rated Voltage	Capacitance (pF)	Code	Tolerance	Rated Voltage
200	201	G, J.	10KV Code: 103	1800	182	G, J.	10KV Code: 103	12000	123	J.	3000V Code: 302
220	221			2200	222			15000	153
270	271			2700	272			22000	223
300	301			3300	332	G, J.	5KV Code: 502	33000	333
330	331			4700	472			47000	473
390	391			5100	512			56000	563
470	471			5600	562			68000	683		1000V Code: 102
560	561			6800	682			82000	823
680	681			7500	752			100000	104
820	821			8200	822			120000	124
1000	102			10000	103
1200	122
1500	152

Numero ng bahagi

Code	G	J
Tolerance	±2%	±5%

Uri at Dimensyon ng Pin ng DLC70L

Yunit: Pulgada (Millimeters)

Termination Code	Type / Outline	Capacitor Dimensions				Lead Dimensions			Terminal Electrode & Lead Material
		Length (Lc)	Width (Wc)	Thickness (Tc)	Termination Size (B)	Length (LL)	Width (WL)	Thickness (TL)	Copper-plated, tin-plated
P	Chip (Non-magnetic)	1.350 ± .050 (34.29 ± 1.27)	1.350 ± .050 (34.29 ± 1.27)	.197 (5.00) max	.039 ~ .071 (1.00 ~ 1.80)	—	—	—	Copper-plated, tin-plated
MN	Microstrip (Non-magnetic)					.748 (19.00) min	1.299 ± .020 (33.00 ± 0.50)	.012 ± .001 (0.30 ± 0.025)	Silver-plated copper strip
AN	Axial leaded (Non-magnetic)					.748 (19.00) min	1.299 ± .020 (33.00 ± 0.50)	.012 ± .001 (0.30 ± 0.025)
FN	Radial leaded (Non-magnetic)					.669 (17.00) min	.157 ± .008 (4.00 ± 0.20)	.012 ± .001 (0.30 ± 0.025)

Kapasidad ng telekomunikasyon

Item	Specification
Quality Factor (Q value)	- Capacitance ≤ 1000 pF: Q ≥ 2000, test frequency 1 MHz. - Capacitance > 1000 pF: Q ≥ 2000, test frequency 1 kHz.
Insulation Resistance (IR)	- ≥ 10⁵ MΩ at 25°C, tested at 500 VDC. - ≥ 10⁴ MΩ at 125°C, tested at 500 VDC.
Rated Voltage (WVDC)	See Capacitance Table.
Dielectric Withstanding Voltage (DWV)	- 500V < Rated Voltage ≤ 1250V: Apply 150% of rated voltage for 5 seconds. - Rated Voltage > 1250V: Apply 120% of rated voltage for 5 seconds.
Operating Temperature Range	-55°C ~ +125°C (Contact Dalicap Technology Co., Ltd. for higher temperature requirements.)
Temperature Coefficient (TC)	0 ± 30 ppm/°C
Capacitance Drift	±0.2% or ±0.05 pF, whichever is greater.
Piezoelectric Effect	None
Termination Type	See Lead Type and Dimension Table.

Pagsusulit sa kapaligiran

Item	Specification	Method
Resistance to Soldering Heat	Appearance: No mechanical damage. Capacitance change: -1.0% ~ +2.0% or 0.5 pF, whichever is greater. Q value: > 1000. IR: Not less than the initial requirement value.	Preheat at 150°C ~ 180°C for 1 minute, immerse in solder at 260 ± 5°C for 10 ± 1 seconds, cool for 24 ± 2 hours, then test.
Thermal Shock	DWV: Meet initial requirements. IR: ≥ 30% of the initial requirement value. Capacitance change: ≤ 0.5% or 0.5 pF, whichever is greater.	Test per MIL-STD-202, Method 107, Condition A. Expose at extreme temperatures for 15 minutes; transition from minimum to maximum operating temperature in ≤ 5 minutes, repeat for 5 cycles.
Moisture Resistance	(Same as thermal shock specs)	Test per MIL-STD-202, Method 106.
Steady-State Humidity Heat	IR: Meet initial requirements. Capacitance change: ≤ 0.3% or 0.3 pF, whichever is greater.	Test per MIL-STD-202, Method 103, Condition A. Apply 1.5 VDC at 85°C, 85% RH for 240 continuous hours.
Life (Endurance)	IR: ≥ 30% of the initial requirement value. Capacitance change: ≤ 2.0% or 0.5 pF, whichever is greater.	Test per MIL-STD-202, Method 108 at extreme temperature for 2000 hours: - 500 VDC < Rated Voltage ≤ 1250 VDC: Apply 1.2× rated voltage. - Rated Voltage > 1250 VDC: Apply rated voltage.
Terminal Strength	Microstrip: > 20N	Test per MIL-STD-202, Method 211.