Mataas na kapangyarihan RFAnd Microwave MLCC

Mataas na kapangyarihan RFAnd Microwave MLCC

Get Latest Price

Min. Order:

Makipag-ugnay sa Ngayon

Paglalarawan ng Produkto

Mga katangian ng produkto

Pagbalot at Paghahatid

Paglalarawan ng Produkto

Mga katangian ng produkto

Model No.: DLC70P(0603)

Pagbalot at Paghahatid

The file is encrypted. Please fill in the following information to continue accessing it

Paglalarawan ng Produkto

DLC70P(0603) RF At Microwave MLCC

Mga tampok ng produkto:

Mataas na halaga ng Q, mataas na kapangyarihan, mababang ESR/ESL, mababang ingay, mataas na dalas ng self-resonant, mataas na pagiging maaasahan.

Mga aplikasyon ng produkto:

Mga karaniwang functional na application: tuning, bypass, coupling, feedback, DC isolation at impedance matching.

Mga karaniwang application ng circuit: Uf/microwave RF power amplifier, mixer, oscillator, low noise amplifier, filter network, timing circuit at delay circuit.

DLC7OP capacitance table

Numero ng bahagi

Uri at sukat ng dulo ng DLC7OP
Yunit: Pulgada (Millimeters)

Toolbox ng disenyo
Nag-aalok ang Dalykapp ng iba't ibang toolkit ng disenyo, at ang mga capacitor na ito ay sumusunod sa mga kinakailangan ng RoHS. Ang bawat uri ng kapasidad ay may 10 capacitor.

Pagganap ng elektrikal

ItemS	pecification
Quality Factor (Q value)	≥ 2000, at 1 ± 0.1 MHz, 1 ± 0.2 Vrms.
Insulation Resistance (IR)	≥ 10⁵ MΩ at 25°C, rated voltage applied. ≥ 10⁴ MΩ at 125°C, rated voltage applied.
Dielectric Withstanding Voltage (DWV)	250% of rated voltage applied for 5 seconds.
Operating Temperature Range	-55°C ~ +125°C (Contact Dalicap Technology Co., Ltd. for higher temperature requirements.)
Temperature Coefficient (TC)	0 ± 30 ppm/°C
Capacitance Drift	±0.2% or ±0.05 pF, whichever is greater.
Piezoelectric Effect	None

Pagsubok sa kapaligiran

Item	Specification	Method
Resistance to Soldering Heat	Appearance: No mechanical damage. Capacitance change: -1.0% ~ +2.0% or 0.5 pF, whichever is greater. Q factor: > 1000. Insulation resistance: Not less than the initial requirement value.	Preheat at 150°C ~ 180°C for 1 minute, immerse in solder at 260 ± 5°C for 10 ± 1 seconds, and test after cooling for 24 ± 2 hours.
Thermal Shock	Appearance: No mechanical damage. Capacitance change: ≤ 0.5% or 0.5 pF, whichever is greater. Q factor: > 2000. Insulation resistance: ≥ 30% of the initial requirement value. DWV: Meet the initial requirement value.	Test in accordance with MIL-STD-202, Method 107, Condition A. Expose at extreme temperatures for 15 minutes, transition time from minimum to maximum operating temperature ≤ 5 minutes, 5 cycles total.
Moisture Resistance	Appearance: No mechanical damage. Capacitance change: ≤ 0.5% or 0.5 pF, whichever is greater. Q factor: > 300. Insulation resistance: ≥ 30% of the initial requirement value. DWV: Meet the initial requirement value.	Test in accordance with MIL-STD-202, Method 106.
Steady State Humidity Heat	Appearance: No mechanical damage. Capacitance change: ≤ 0.3% or 0.3 pF, whichever is greater. Q factor: > 300. Insulation resistance: Meet the initial requirement value.	Test in accordance with MIL-STD-202, Method 103, Condition A. (Apply 1.5V DC voltage at 85°C, 85% RH for 240 hours.)
Life (Endurance)	Appearance: No mechanical damage. Capacitance change: ≤ 2.0% or 0.5 pF, whichever is greater. Q factor: > 500. Insulation resistance: ≥ 30% of the initial requirement value.	Test in accordance with MIL-STD-202, Method 108. Apply 2× rated voltage at extreme temperature for 2000 hours.